Foldable / collapsible pedals with 9/16 inch thread and reflectors.
For space-saving storage or transport!
Details:
Thread: 9/16 inch
Design: Platform pedal
Material: Stable pedal body made of durable thermoplastic
Axle: Boron steel
Colour: black
Weight: ~ 290 g
Platform dimensions: 90 x 75 x 25 mm
With StVZO approved reflectors
1 pair of pedals
Original accessories for bikes from Urban Drivestyle Berlin!
Tektro EL 350 cn left side (only for e-bikes)Brake lever for use on e-bikesFor use also with linear pull brakes and Rapidfire shiftersLever and bracket made of cast aluminium4-finger lever bladepower cut - off brakeFunction of a power cut - off brakeThere is a sensor that sends a signal to the control unit when the brake lever is pulled to switch off the motor.Mounting side: leftWeight: 108 g.Scope of delivery: 1 piece
Conical spacer from Ritchey for semi-integrated headsets.
Spacers made of high-strength plastic for the steerer tube to adjust the height of the stem and handlebar.Conically shaped for a more beautiful appearance
Material: plasticfor 1 1/8" steerer tubeColor: glossy blackHeight: 15 mmDiameter inside: 29 mmDiameter outside bottom: 50 mmDiameter outside top: 36 mmWeight ~ 11 g
Tire 24 x 3.0 cream
75-507
Semi Slick
Thick and strong tire for up to 20- 35 PSI pressure
Mounted approx. 75 mm wide
Total diameter depending on rim width and air pressure approx: 65.3 + / - 2 cm
Weight: approx. 1.6 kg
This tire fits all CLASSIC CYCLE 24" rims up to approx. 82 mm width! However, please note clearance in frame and / or fork!
Do not inflate the tire with 82 mm wide rims over 1.5 bar. There is a risk that the flank wire tears (-applies to all tires on extra-wide rims)
Shown is the tire mounted on a 82 mm wide rim from us.
1 piece
Tire 26 x 3.0 cream
75-557
Semi Slick
Thick and strong tire for up to 20- 35 PSI pressure
Mounted approx. 75 mm wide
Total diameter depending on rim width and air pressure approx: 705 mm + / - 20 mm
Weight: approx. 1.9 kg
This tire fits all CLASSIC CYCLE 26" rims up to approx. 82 mm width! However, please note clearance in frame and / or fork!
Do not inflate the tire with 82 mm wide rims over 1.5 bar. There is a risk that the flank wire tears (-applies to all tires on extra-wide rims)
Shown is the tire mounted on a 82 mm wide rim from us.
1 piece
Double crown fork 800 mm chrome plated 1 inch shaftchrome-plated, 1 inch shaftshaft length: 250 mm
Hiten steel with forged aluminum bridge, disc brake mountLength of fork tubes: 800 mm, Width between fork tubes: ~ 93 mm.Diameter of the standpipes: ~ 32mmInner diameter of the standpipes: ~ 29 mmAxle mount: 100 mmThe shaft length can be changed during installation, via the mounting height of the bridges.The shaft has a M6 hole at the bottomWeight: ~ 2.6 kg
Brake cable for front, pre-assembled
Outer cover:
~ 80 cm long
with end caps
Inner cable:
~ 96 cm long
diameter: ~ 1,5mm
with cylinder nipple ~ 7 x 6 mm
1 piece
Charging socket XLR D 3-pole, female with sealing cap / sealing housing
Info about the XLR D 3-pole female charging connector:
Traditional chassis connector with large solder pads for easy soldering.
3-pole female chassis connector, D-shape
Solder terminals
Black plastic housing
Gold plated contacts
Info about the Neurik SCDX sealing cap / sealing housing:
With the SCDX sealing cap, D-shape chassis connectors are sealed against water, dust and dirt according to IP42 when unmated.
IP42 protection against dust and splash water
Suitable for all D-shape flush-type connectors
Snap lock
Labelling area
The dimensions of the sealing cap can be found in the data sheet below.
Scope of delivery:
1x XLR D receptacle
1x sealing cap
Alu Rim 24 inch., 102 mm (~4,01 inchesa) wide, silver raw
No Holes
The ultimate wheel for custom style choppers / cruisers!
Fits perfect on wide tires!
This offer includes: 1 x rim without any holes for self drilling fans
wide:
100 mm (~4,01 inches)
Inner size:
94 mm (~3,70 inches)
holes:
0
colour:
silver raw
Diameter to calculate the length of the spokes:
486 mm (~19,13 inches)
All 24" Classic Cycle tires 3.0 and wider fit on these rims! But please check frame/fork for clearance!
Stem Steel black Humpert Ergotec CV 102
Original NOS from Humpert Germany
NOS= New Old Stock
Oldschool 70-90s
black
Handlebar mount with single bolt: 25,4 mm (~1 inch)
25,4 mm (~1 inch) shaft
180 mm (~7,09 inches) shaft height
110 mm (~4,33 inches) nosing with 45° angle
Using a single bolt mount won't recommend handle bars with big hights.
T-Shirt "PG", green
with PG crown imprint on the front
high quality cotton
please choose Your size: S M L XL
these high quality shirts come from the insolvency of the PimpGarage TM Custombikes GmbH
the original price was 29,99 € !!!
Greaser fuel tank cover Set ivory
Set for right and left side
Dyed plastic
Total length: ~ 71,5 cm (~28,15 inches)
Maximum height: ~ 16,5 cm (~6,50 inches)
LIU, the Lady Frame, more curvaceous in its form, is exceptional and comfortable. Made of 25x25 mm and 20x20mm quadrangle tube. The frame length is approx. 115 cm, the full length is approx. 200 cm
RIM
24’ 26’ 28’
Button Part shell / lug
US/BMX
HEAD TUBE
1.⅛ , 120MM
SEATPOST
28,6 mm FITS SEATPOST CLAMP 31,8mm
DISC BRAKE
"No"
COASTER BRAKE
YES
HEAD TUBE TO SEATPOST
72 CM
SEATPOST TO BOTTOM BRACKET SHELL
55 CM
MATERIAL
plain steel, unpainted
Weight: ~ 6,9 kg
It’s suitable for thousands of different configurations, letting you fully unleash your customizer creativity: it can fit basically any component on the market like:
forks (cruiser, double crown, springer)
rims (24″, 26″ – widths of up to 102 mm (~4 inches), front wheel also supports 28″ rims)
tires (24″, 26″ up to 4″)
handlebars (every brand on the market)
hubs (coaster hub, automatic gear shift, integrated gear hub)
It’s the perfect choice for those who want to be a notch above yet without sacrificing riding pleasure and comfort: when riding it you surely will not go unnoticed!
CHAIN DEFLECTOR 34,9 mm / 1,37 inches
Prevents chain from falling down and jamming.
diameter 34,9 mm / 1,37 inches
mounting on the seat tube
made of black plastic
Weight: 9g
20 sets of saddle rail / frame for Victor Hammock, Release-type
Classic style from the 1898 to the 1920s
frame / rails are raw and duly oiled
including rivets
only available in a 20 sets package
T-shirt dark gray
with PimpGarage TM on the chest
Your size: M
The T-shirts are produced very high quality and in best condition.
The T-shirts are from the insolvency of PimpGarage TM Custombikes GmbH.
The original price of the T-shirts was € 29.99
Chainwheel Poker stainless steel, 44 teeth
Cool chainwheel for "one piece crank", 44
For chains 1/2 x 1/8
Stainless steel
44 teeth (the chainwheel would have 44 teeth if it were continuously toothed)
Original GANT Lautaret 1970s vintage bicycle gloves with chrocheted upper hand
The inner hand is made out of finest soft glove leather with light padding.
Upper hand: chrocheted cotton
Inner hand: finest soft glove leather with light padding
Size: 7
Color: white with blue and red stripes
Scope of delivery: 1 pair gloves
Genuine leather
Made in France by Gant 41100 Vendome
Racer Lautaret
NOS New Old Stock ~ 1970s - 1980s
Tire Liner for tires 20-29 inch
Easy installing between Tube and Tire.
Tire Liners are reusable and are made of PUR POP material.
They will provide a lifetime of protection from puncture caused by sharp objects.
One Roll
Width: 80 mm (~3,15 inches)
Thick: 1,1 mm (~0,043 inches)
Length: 50 m ( ~ 164 ft)
Assembling instruction:
Remove the wheel and let the air out of the tube.
Remove tire and tube from rim.
Make sure that the inside of the tire is free from sharp bodies.
Place a puncture protection insert in the tire. The ends can overlap by 7 - 10 cm.
Please shorten to the required length.
Inflate the tube a little (0,5 BAR / 7 PSI) and place back in the tire.
The puncture protection insert is fixed by the tube.
Mount the tire and tube on the rim and inflate to the desired tire pressure.
ELECTRA Rally Sport original Front Fender 26" metallic green
26"
NOS
painted with white Stripes
Short Fender
without fixing material and Stays
Scope of delivery: 1 Front fender
Wide: ~ 80 mm (~ 3.15 inches)
Height: ~ 26 mm (~ 1.02 inches)
Lenght in circumference: ~ 400 mm (~15.75 inches)
Diameter inside: ~ 305 mm (~ 12.01 inches)
Diameter outside: ~ 380 mm (~ 14.96 inches)
ELECTRA Rally Sport original Rear Fender 26" mettalic green
26"
NOS
painted with white Stripes
Short Fender
without fixing material and Stays
Scope of delivery: 1 Rear fender
Wide: ~ 80 mm (~ 3.15 inches)
Height: ~ 26 mm (~ 1.02 inches)
Lenght in circumference: ~ 540 mm (~21.26 inches)
Diameter inside: ~ 390 mm (~ 15.35 inches)
Diameter outside: ~ 495 mm (~ 19.49 inches)
On the rear Fender, on the chain side, there is a standard housing for the chain run
ELECTRA Betty original Front Fender matt white/black
for 24 x 3.0 tyres
NOS
painted with with grey/red flames
without fixing material and Stays
Scope of delivery: 1 Front Fender
Wide: ~ 80 mm (~ 3.15 inches)
Height: ~ 26 mm (~ 1.02 inches)
Lenght in circumference: ~ 730 mm (~ 28.74 inches)
Diameter inside: ~ 520 mm (~ 20.47 inches)
Diameter outside: ~ 595 mm (~ 23.43 inches)
ELECTRA Indy original Rear Fender 26" red
26"
NOS
painted with black/golden stripes
May contain storage marks
without fixing material and Stays
Scope of delivery: 1 Rear fender
Wide: ~ 80 mm (~ 3.15 inches)
Height: ~ 26 mm (~ 1.02 inches)
Lenght in circumference: ~ 1220 mm (~48.03 inches)
Diameter inside: ~ 660 mm (~ 25.98 inches)
Diameter outside: ~ 710 mm (~ 27.95 inches)
On the rear Fender, on the chain side, there is a standard housing for the chain run
Carrier alu yellow fits 27/28 inch tires
NOS New Old Stock ~ late 1990s
Made in Taiwan
Usage
City, Crossrad, Streetracer
Alu Die-Cast
Package comes with
one carrier
including adjustable bracket for mounting on the seat post clamping screw
including strut bracket with rubber cover and stainless screws
including reflector bracket
Material
Color: yellow
Attachments on eyelets, seat stay or chain stay
Stainless screw connectors
Technical specification:
Number of struts: 6
Strut attachment to the braze-on base of the frame dropout or seat stay or chain stay
Strut length 340 mm
Weight rack: light ~ 480 g
Dimensions of the rack: ~ 315 x 130 mm
Original NOS
New Old Stock
Shifter by Sachs Huret for mounting on handlebar stem.
made in france
Mounting for stem shaft : 22 mm (0.87 inch)
with pre-mounted shift cables
Front Wheel 26 inch flat black 24,5 mm (~0,96 inches) Alu , Novatec
Rim data:
Ventura Double hollow section rim with CNC roughened brake flanks (GBS) with wear indicator.
height: 18 mm / 0,71 inches
Width outside: 24.5 mm / 0,96 inches
Width inside: 19 mm / 0,75 inches
ERD: 533 mm / ~ 21 inches
ETRTO: 559
Auto or Dunlop valve
36 hole
matt black powder coated
with rim tape
Spokes and nipples
36x 2,0 mm spokes stainless steel, 14 G = 2 mm
nipple silver
hub
Novatec high quality hub
Aluminum
silver polished to high gloss
industrial bearing
36 holes
quick release
Axle:
Alloy silver polished, quick release
Installation width:
100 mm / 3,94 inches
With:
26 inch 559 alloy rim 24.5 mm /
width outside:
24,5 mm (~0,96 inches)
inner size:
19 mm (~0,75 inches)
Holes:
36 holes 14 G = 2 mm (~0,078 inches)
colour:
Black powdercoated
Tire Dragster Slick 20 x 3.0 pure black
Originally used on the extra cool late 60s Schwinn Sting-Ray, Krates or Muscle Bikes. Nostalgia tire for the ultimate old school look!
72-406
Dragster Sting Ray Slick
Big and strong tire for up to 35 PSI pressure.
This tire fits on all 20" Classic Cycle rims up to 67 mm (~2,6 inches) width!
Mounted on a 67 mm / 2,6 inches wide rim, the tyre has approximately the following dimensions:
It protrudes ~ 60mm / ~ 2,3 inches above the rim edge, is ~ 76 mm / ~ 3 incheswide and has an overall diameter of ~ 545 mm / ~ 21,5 inches.
Scope of delivery: 1 tire
Classic Fender Set steel 26 inch black, with holes for dress guard
fender set for 26 inch. bikes, black, incl. wire struts and assembling parts
for Bicycles from the 30s till 50s, Dutch Types or similar
Historical pattern made out of steel
Complete Set front and rear
Glossy black
width: 58 mm (~2,28 inches)
height: 22 mm (~0,87 inches)
Inside diameter: approx. 670 mm (~26,38 inches)
Outside diameter: approx. 720 mm (~28,35 inches)
Rear fender with 60 holes for dress guards (30 holes per side)
Fender stays / wire to mount on axle
weight: ~ 880 gr. (~1,94 pounds)
Hebie 664 self-folding side stand for bicycles / parking stand
The Hebie 664 self-folding side stand in black for bicycles and S-Pedelecs - specially modified for the UNI Bikes from Urban Drivestyle Berlin, but of course also universally usable for other 20 inch bicycles - quality made in Germany.
The stand is super sturdy and provides a stable parking position for your UNI MK, UNI Swing or UNI Bobber e-bike. The standardized threaded hole spacing is 40mm KSA.
The Hebie 664 is the self-folding version of the Hebie 661. The stand folds automatically when the bike is unloaded and brought into riding position.
Note: Do not lean / sit on the bike when it is parked on the stand, as it is designed to hold the bike's own weight, but not the additional weight of a person sitting on the bike!
Features of the side stand
Brand: Hebie
Material: Coated steel
Color: Black
Mounting:
Direct mounting on the frame by KSA 40 (special mount on the chain stay).
Hole spacing 40 mm, with threaded through hole
Dimensions: ~ 27cm x 9cm x 4cm (L x W x H)
Weight: ~ 300g
Includes: Side stand & attachments
Universal bike stand, suitable for 20 inch bikes
Self-folding through unloading
Stepless length adjustment without tools
Load capacity: 25 kg
Made in Germany
Original accessories from Urban Dirvestyle Berlin!
UD Cassette freewheel screw on Mijnen Pieper 7-Speed 14 - 28 T
Type City, MTB, Race
Material Steel
Speed 7-speed
Color Nickel plated
Range 14-28T
Urban Drivestyle Berlin had used these parts on their bikes
48V Charger for Li-Ion Battery with DC Plug
Input: 110 - 240 V ~ 50/60 Hz 2.0 A
Output: 54,6V 2.0 A
Operating and storage temperature: 0 ~ 30° C (~ 32 - 86 ° F)
low noise
complies with all European standards
Note: The charger housing may differ from the illustration.
Hope brake adapter N for PM to IS rear wheel 180 mm silver.
Hope adapter for mounting postmount brakes on IS2000 frames. Can be used for rear wheels with 180 mm brake disc.
Please also note the data sheet below when choosing the right adapter!
Post Mount to IS
for 180 mm rear brake disc
incl. mounting bolts
silver
Nutt hydraulic brake right side for e-bikes with power cut - off.
Brake lever for use on e-bikes
Hydraulic brake
With power cut - off
Function of a power cut - off:
There is a sensor that sends a signal to the control unit when the brake lever is pulled to cut off the motor.
Mounting side: right
Weight: ~ 110 g.
Scope of delivery: 1 piece
Double crown fork 800 mm black 1 inch shaftblack anodized, 1 inch shaftshaft length: 250 mm
Hiten steel with forged aluminum bridge, disc brake mountLength of fork tubes: 800 mm, Width between fork tubes: ~ 93 mm.Diameter of the standpipes: ~ 32mmInner diameter of the standpipes: ~ 29 mmAxle mount: 100 mmThe shaft length can be changed during installation, via the mounting height of the bridges.The shaft has a M6 hole at the bottomWeight: ~ 2.6 kg
Double crown fork 570 mm black 1 inch shaftblack anodized, 1 inch shaftshaft length: 250 mm
Hiten steel with forged aluminum bridge, disc brake mountLength of fork tubes: 570 mm, Width between fork tubes: ~ 93 mm.Diameter of the standpipes: ~ 32mmInner diameter of the standpipes: ~ 29 mmAxle mount: 100 mmThe shaft length can be changed during installation, via the mounting height of the bridges.The shaft has a M6 hole at the bottomWeight: ~ 2.0 kg
Brake cable for rear, pre-assembled
Outer cover:
~ 150 cm long
with end caps
Inner cable:
~ 166 cm long
diameter: ~ 1,5mm
with cylinder nipple ~ 7 x 6 mm
1 piece
Chain Cover Original ELECTRA Amsterdam copper
painted with sticker
dimensions: ~ 735 x 210 mm (~28,94 x 8,27 inches)
Front hole outer side: diameter ~105 mm ( ~ 4 ,13 inch)
Front hole inner side: diameter ~ 34,5 mm ( ~ 1,35 inch)
Overall diameter: ~200 mm ( ~ 7,87 inch)
Overall diameter for the sproket ~ 127 mm ( ~ 5 inch)
€24.95*
This website uses cookies to ensure the best experience possible. More information...