Motor extension cable Julet 9 PIN, 70 cm / 27,56 inches

Pre-assembled Bafang wiring harness 1T4 with 2PIN extension cable in cable protection hose. Technical data of Bafang wiring harness 1T4: Transmission of power and data between the controller and the brake sensors, thumb throttle and display. Compatible with Bafang hub motors Waterproof plugs / connectors Cable length: ~ 70 cm / 27,55 inches, incl. connector ~ 80 cm / 31,5 inches Connections: 1x male 3-PIN Julet connector yellow for throttle / thumb throttle. 1x male 5-PIN Jullet connector green for display 2x female 3-PIN Jullet connector yellow for shift / brake sensor 1x male 8-PIN Jullet connector black for controller Technical data of Extension cable for Ebike: Connector: 2-pin HIGO / Julet (1x male - 1x female) Water resistance: IP65 Cable length: 100 cm / 39,37 inches Plug connection: red Outer material: ABS plastic Technical data cable protection hose: Keeps cables tidy and protected! Diameter: ~ 20 mm Length: ~ 850 mm Fabric hose with practical Velcro fastener over the entire length General information: HIGO / Julet plugs are common on many e-bikes because they provide a firm and waterproof connection. There are different types, which differ in the number of pins and thus the area of use. A HIGO / Julet connector is generally quite firm because it is waterproof. It can be disconnected by pulling, NOT twisting. If twisted, the pins could be damaged. Please note the arrows on the outside - they help to align and fit the connectors. When the connections are properly plugged together, no coloured plastic should be visible.

Thumb throttle for ebike or pedelec female Control the power of your motor from the comfort of your handlebars! The thumb throttle is simply connected / connected to the wiring harness of your bike thanks to the 3 PIN female Jullet Higo, Nexmo connector. Details: Connectors: 3 PIN female Jullet, Higo, Nexmo, yellow. Cable length: ~ 47 cm Mounting: handlebar with 22.2 mm diameter, left and right handlebar side possible compatible with Bafang motors Original thumb throttle from Urban Drivestyle Berlin!

Extension cable for Ebike Technical data: Connector: 2-pin HIGO / Julet (1x male - 1x female) Water resistance: IP65 Cable length: 100 cm / 39,37 inches Plug connection: red Outer material: ABS plastic General information: HIGO / Julet plugs are common on many e-bikes because they provide a firm and waterproof connection. There are different types, which differ in the number of pins and thus the area of use. A HIGO / Julet connector is generally quite firm because it is waterproof. It can be disconnected by pulling, NOT twisting. If twisted, the pins could be damaged. Please note the arrows on the outside - they help to align and fit the connectors. When the connections are properly plugged together, no coloured plastic should be visible.

BAFANG Urban Drive Style Controller 48V Rated voltage: 48V off Voltage:  41,5 +/- 1V: Electric current: 18A +/- 1 A Original Item from Urban Drivestyle Berlin! The controller was installed on the UNI Boost with a setting of 20x4 and a maximum speed of 20 km/h.  

DC converter / voltage transformer with HIGO / Julet connections Input: 7 - 60 VDC Connector: 1x 2-pin HIGO / Julet female, red Output: 12V / 1000 mA Connector: 2x 2-pin HIGO / Julet male, red Total length incl. plug: ~ 30 cm Converter size: 43 x 21 x 10 mm General information: HIGO / Julet plugs are common on many e-bikes because they provide a firm and waterproof connection. There are different types, which differ in the number of pins and thus the area of use. A HIGO / Julet connector is generally quite firm because it is waterproof. It can be disconnected by pulling, NOT twisting. If twisted, the pins could be damaged. Please note the arrows on the outside - they help to align and fit the connectors. When the connections are properly plugged together, no coloured plastic should be visible.

204 MXUS Motor 500W Rear wheel 20 x 4 - 80 mm wide 20 inch rear wheel matt black coated aluminium rim ~ 80 mm / 3,15 inches wide 36 spokes 2,6 mm / 0,1 inches disc brake mount ~44 mm / 1,73 inches 6 hole Hub installation dimension approx.: ~ 190 mm / 7,5 inches aluminium hub with industrial bearings 500W 48V Fixed axle: ~ 12 mm / 0,47 inches diameter Axle length: ~ 265 mm Mounting for cassette Rim width: ~ 80 mm / 3,15 inches With rim tape Weight: ~ 4800 g / 10,58 lbs Specification Motor: Model number GDR-15FAT-1 Position Rear Construction Gear Rated voltage(V) 48 Rated Power(W) 500 Weight(kg) 4.15 Reduction Ratio 1:5 Wheel Diameter(inch) 20 Rated speed(km/h) 25-40 Magnet Poles(2P) 10 Dropout(mm) 190 Brake Type Disk brake Operating Temperature © -20 - +45 Efficiency(%) ≧78% Color Black Cabling Route Shaft center right Noise Grade(dB) ≤55 IP Grade IP54 Salt Spary Test Standard(h) 24/96