204 Bafang wheel front die-cast aluminium, 20 x 4
Technical specifications front wheel:
Position: front wheel
Wheel diameter (inches): 20
Colour: Black / Silver
Installation parameters front wheel:
Installation width: 135 mm
Max. Diameter rim: 422 mm
Brake: Disc brake mount, 44 mm 6 hole
Special features:
Including installation material like pictured.
Weight: ~ 3,3 kg
Dimensions:
Dim A
100 mm
Dim B
76.6 mm
Dim C
422 mm
Dim D
44 mm
Dim E
33 mm
Dim F
2-M12X1.25-6g
Dim G
0
Dim H
26.5 mm
Dim I
15.25 mm
Dim OLD
175 mm
Dim WL
87.5 mm
Dim WR
87.5 mm
Brake cable for front, pre-assembled
Outer cover:
~ 80 cm long
with end caps
Inner cable:
~ 96 cm long
diameter: ~ 1,5mm
with cylinder nipple ~ 7 x 6 mm
1 piece
Brake cable for rear, pre-assembled
Outer cover:
~ 150 cm long
with end caps
Inner cable:
~ 166 cm long
diameter: ~ 1,5mm
with cylinder nipple ~ 7 x 6 mm
1 piece
Brake pads for disc brakes, blue
Carrier plate: steel, blue
Dimensions of carrier plate: L: 30 mm, H: 20 mm, total height incl. pin holder: 35 mm
Scope of delivery: 2x brake pads, as illustrated
Busch + Müller dynamo rear light Toplight Flat plus
The classic.
Design: extremely flat and light, elegant reflector integrated into two circular surfaces. 70 g light.
Like all Busch + Müller rear lights: StVZO-approved.
Toplight series
Parking light
Dynamo version
StVZO-approved
Mounting luggage carrier
LED rear light
Integrated Z-large area reflector
Weight: ~ 70 g
Dimensions: ~ 33 x 112 x 54 mm
Disc Brake Adapter Front IS / PM TEKTRO A5 Disc 203 mm
TRP Tektro A5 IS/PM Adapter Front 203mmThe TRP Tektro A5 IS/PM adapter for fork with IS mount and 203mm brake disc in combination with postmount caliper.
Details:
Fork/frame type: IS (International Standard).
Brake caliper type: Postmount
Brake disc diameter: 203mm front
Weight: approx. 60 g
incl. mounting bolts
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Dished Sprocket, 10 mm (~0,39 inches) offset, 22 Teeth
1/2 x 1/8
22 Teeth
helps to bring the chain about 10 mm (~0,39 inches) out
Depth: ~ 15 mm (~0,59 inches)
50 Rebels EBike
URBAN - ROBUST - Made in Portugal
The ideal e-bike for individualists.
Thanks to the sleek and simple design, you can customize the Rebel to your very own personal bike.
Technical Specifications:
Motor:
Bafang 250 Watt rear hub G60
Battery:
48V, 15 Ah, removable
Range:
approx. 70 - 80 km / 43 - 49 miles per load (depending on incline, motor assist level, temperature and rider weight)
Charging time:
approx. 6 - 8 hours
Speed:
up to max 25 km/h (15,53 mph)
Speed Contol:
PAS (Pedal Assist System) 12 Magnet Cadace Sensor, 5 assistance levels
Display:
Bigstone C600E
Walk assist:
yes
Certification:
EN15194
Warranty:
according to the legal german requirements
Weight:
~ 30 kg / ~ 66 lbs
Dimensions:
L 165 x H 114 - 120 x B 70 cm / 65 L x 45 - 47 H x B 27,5 inch
Seat height:
~ 85 cm / 33 inch
Handlebar height / width:
~ 114 cm (45 inch) - 120 cm (47 inch) adjustable / 70 cm ( 27,5 inch )
Frame:
Carbon steel
Fork:
Carbon steel and Aluminum
Gear:
Shimano ALTUS RDM310
Brake:
Mechanical Disk Brakes
Crankset:
52T Aluminium
Tires:
20 x 4.0 CST Megatane
Lights:
Front light bar 3W, back light strip 2W
Bike maximum load:
~ 130 kg / ~ 286 lbs
Factory setting: E-Bike is regulated by 25 kmh (15,53 mph) and doesn't need approval.
Please notice: The Pedelec doesn't come with light installation according to german StVZO and DIN97100. Please choose by yourself where to use the Pedelec.
Rayvolt Ringo - The Street Cowboy
Off-Road yet Urban. Compact but generous. Vintage yet modern.
Ringo is a stylish post-apocalyptic looking compact bike, made for the city and the road with an all terrain versatility. This practical two-seater bike has a head-spinner look, that will let you be the eye-catcher of the road, while riding with someone on the back. This bike combines a great look, a comfortable position, and the features of all the latest Rayvolt smart technology.
Ringo has an intelligent regenerative brake system.
The electronic braking system, fitted into the brake levers, sends a data signal to the motor controller that provokes a reverse effect in the motor. This converts torque into resistance using the wheel inertia to generate electricity and recharge the batteries.
In simple words, the regenerative braking acts like an ultra powerful dynamo when the levers are pulled.
The Eiva2.0® is a Rayvolt's developed software to control, customize and monitor your Rayvolt bike.
An Eiva® computer can be purchased and secured mounted to the handlebars, ready to go whenever you are. The software can also be downloaded for use on an existing Android or iPhone.
Technical Specifications:
Motor:
250 Watt Smart Hub 50 Nm
Battery:
36V, 12.5 Ah, removable
Range:
approx. 50 km / 31 miles per load (depending on incline, temperature and rider weight)
Charging time:
approx. 3 hours
Speed:
up to max 25 km/h (15,53 mph)
Speed Contol:
PAS (Pedal Assist System)
E-Drive System:
Rayvolt EIVA® Drive
Walk assist:
yes
Certification:
EN15194
Warranty:
according to the legal german requirements
Weight:
~ 29 kg / ~ 64 lbs
Dimensions:
L 1687 x H 980 x B 700 mm / L 66,42 x H 38,58 x B 27,56 inch
Frame:
A6061 Aluminium
Fork:
45 mm Double Crown
Gear:
Shimano 7 gear
Brake:
Oil Disk Brakes with E-Regenerative 10A - 50A
Rims:
Double wall 20" x 80 mm
Tires:
20 x 4 1/4
Bike maximum load:
~ 130 kg / ~ 270 lbs
Factory setting: E-Bike is regulated by 25 kmh (15,53 mph) and doesn't need approval.
Please notice: The Pedelec doesn't come with light installation according to german StVZO and DIN97100. Please choose by yourself where to use the Pedelec.
Important: The images may show special equipment, in this case front lamp and bag.
Rayvolt Ringo - The Street Cowboy
Off-Road yet Urban. Compact but generous. Vintage yet modern.
Ringo is a stylish post-apocalyptic looking compact bike, made for the city and the road with an all terrain versatility. This practical two-seater bike has a head-spinner look, that will let you be the eye-catcher of the road, while riding with someone on the back. This bike combines a great look, a comfortable position, and the features of all the latest Rayvolt smart technology.
Ringo has an intelligent regenerative brake system.
The electronic braking system, fitted into the brake levers, sends a data signal to the motor controller that provokes a reverse effect in the motor. This converts torque into resistance using the wheel inertia to generate electricity and recharge the batteries.
In simple words, the regenerative braking acts like an ultra powerful dynamo when the levers are pulled.
The Eiva2.0® is a Rayvolt's developed software to control, customize and monitor your Rayvolt bike.
An Eiva® computer can be purchased and secured mounted to the handlebars, ready to go whenever you are. The software can also be downloaded for use on an existing Android or iPhone.
Technical Specifications:
Motor:
250 Watt Smart Hub 50 Nm
Battery:
36V, 12.5 Ah, removable
Range:
approx. 50 km / 31 miles per load (depending on incline, temperature and rider weight)
Charging time:
approx. 3 hours
Speed:
up to max 25 km/h (15,53 mph)
Speed Contol:
PAS (Pedal Assist System)
E-Drive System:
Rayvolt EIVA® Drive
Walk assist:
yes
Certification:
EN15194
Warranty:
according to the legal german requirements
Weight:
~ 29 kg / ~ 64 lbs
Dimensions:
L 1687 x H 980 x B 700 mm / L 66,42 x H 38,58 x B 27,56 inch
Frame:
A6061 Aluminium
Fork:
45 mm Double Crown
Gear:
Shimano 7 gear
Brake:
Oil Disk Brakes with E-Regenerative 10A - 50A
Rims:
Double wall 20" x 80 mm
Tires:
20 x 4 1/4
Bike maximum load:
~ 130 kg / ~ 270 lbs
Factory setting: E-Bike is regulated by 25 kmh (15,53 mph) and doesn't need approval.
Please notice: The Pedelec doesn't come with light installation according to german StVZO and DIN97100. Please choose by yourself where to use the Pedelec.
Important: The images may show special equipment, in this case front lamp and bag.
Rayvolt Ringo - The Street Cowboy
Off-Road yet Urban. Compact but generous. Vintage yet modern.
Ringo is a stylish post-apocalyptic looking compact bike, made for the city and the road with an all terrain versatility. This practical two-seater bike has a head-spinner look, that will let you be the eye-catcher of the road, while riding with someone on the back. This bike combines a great look, a comfortable position, and the features of all the latest Rayvolt smart technology.
Ringo has an intelligent regenerative brake system.
The electronic braking system, fitted into the brake levers, sends a data signal to the motor controller that provokes a reverse effect in the motor. This converts torque into resistance using the wheel inertia to generate electricity and recharge the batteries.
In simple words, the regenerative braking acts like an ultra powerful dynamo when the levers are pulled.
The Eiva2.0® is a Rayvolt's developed software to control, customize and monitor your Rayvolt bike.
An Eiva® computer can be purchased and secured mounted to the handlebars, ready to go whenever you are. The software can also be downloaded for use on an existing Android or iPhone.
Technical Specifications:
Motor:
250 Watt Smart Hub 50 Nm
Battery:
36V, 12.5 Ah, removable
Range:
approx. 50 km / 31 miles per load (depending on incline, temperature and rider weight)
Charging time:
approx. 3 hours
Speed:
up to max 25 km/h (15,53 mph)
Speed Contol:
PAS (Pedal Assist System)
E-Drive System:
Rayvolt EIVA® Drive
Walk assist:
yes
Certification:
EN15194
Warranty:
according to the legal german requirements
Weight:
~ 29 kg / ~ 64 lbs
Dimensions:
L 1687 x H 980 x B 700 mm / L 66,42 x H 38,58 x B 27,56 inch
Frame:
A6061 Aluminium
Fork:
45 mm Double Crown
Gear:
Shimano 7 gear
Brake:
Oil Disk Brakes with E-Regenerative 10A - 50A
Rims:
Double wall 20" x 80 mm
Tires:
20 x 4 1/4
Bike maximum load:
~ 130 kg / ~ 270 lbs
Factory setting: E-Bike is regulated by 25 kmh (15,53 mph) and doesn't need approval.
Please notice: The Pedelec doesn't come with light installation according to german StVZO and DIN97100. Please choose by yourself where to use the Pedelec.
Important: The images may show special equipment, in this case front lamp and bag.
1/2" to 9/16" Pedal Thread Adaptors
Black, CRO MO
These adaptor bushings have a male 1/2"-20 thread to fit into your one-piece crank, and a standard 9/16"-20 female thread that will let you install standard 9/16" pedals, even modern clipless pedals.
These install with a 15 mm (~0,59 inches) pedal wrench.
Length over all: 32 mm (~1,26 inches)
Brings the pedal 21 mm (~0,83 inches) more out
Weight 54 gr. (~0,12 pounds)/pair
Perfect Quality
9/16 Zoll = 14.28 mm
11/20 Zoll = 14 mm
1/2 Zoll = 12.7 mm
"E-Huntsman 20 x 4.0 inch tyre"
20" fatbike tyre specially developed for e-bikes!The E-Huntsman promises high riding comfort on the road as well as on loose off-road surfaces.The override technology guarantees increased puncture protection.For customs or chopper bikes like the Schwinn New Stingray, UNI MK, Super 73, Mate X, Mario and many more!This tyre fits CLASSIC CYCLE 20" rims from approx. 50 mm width! However, please note clearance in frame and/or fork!
Dimensions / Details:
ETRTO: 102 x 406
Max: 36 PSI / 2,5 Bar / 250 kPa
Over Ride E-Bike ready 50
Material: EndC - Endurance Compound
Mounted on an 82 rim, the tyre is approx. 10 cm / 3,93 inches wide and protrudes ~ 9 cm / 3,54 inches above the rim edge.
Total diameter: 60 cm / 23,62 inches
Offered is a tyre without rim.
Weight: ~ 2250 g / ~ 4,96 lbs.
204 Fat Bike Plastic Fender Set 20 x 4.0 - 4.8 inch. Fender Stays 124 mm (~4,88 inches) width
Mudguards with four stainless steel struts and mounting hardware for Fat Bikes 20 x 4.0 - 4.8 or similar.
Due to the variably adjustable struts, the mounting points on the frame can be flexibly selected.
The fenders are therefore also suitable for many common 20-inch Fat E-bikes.
124 mm (~4,88 inches) wide, 20 inch., black matte
complete plastic fender set for Fat Bikes or similar bike types
Width: 124 mm (~4,88 inches)
Hight: 35 mm (~1,38 inches)
Diameter inside: ~ 550 mm (~21,65 inches)
Diameter outside: ~ 610 mm (~24 inches)
Rear length in circumference: ~ 960 mm (~37,8 inches)
Front length in circumference: ~ 620 mm (~24,4 inches)
Polycarbunate plastic black matte
Weight: ~ 1080 g. (~2,65 pounds)
Tire Kenda Kraze 20 x 4 1/4
97-406
THE ultra fat custom tire with oldschool tread
The ultimate custom cruiser tire for maximum performance!
On 82 mm (~3,23 inches) rim as shown it is 98 mm (~ 3,86 inches) wide and 61 mm (~ 2,4 inches) high (above the rim).
This tire fits rims of widths 67 mm (~2,64 inces) to 102 mm (~4,02 inches) width!
If you assemble the tire on wide rims not to put more pressure than 30 PSI. It could blast.
But please check frame/fork for clearance!
Weight: 1430 g (~ 3,15 pounds)
30 TPI
204 Kenda Krusade Extra Wide Tire 20 x 4
Diameter: 406
98 - 406
Ideal for the 20 inch fat e-bikes!
This tire fits on all 20" Classic Cycle rims wider than 67 mm (~2,64 inches) ! But please check frame/fork for clearance!
On a 82 mm (~3,22 inches) rim the tire is about 95 mm (~3,74 inches) wide and it will 79 mm (~3,11 inches) protrude over the rim.
Diameter over all on this rim: 580 mm (22,83 inches)
60 TPI
5-30 PSI / 0,4 -2.1 bar / 40 - 210 KPA
Weight: ~ 990 g (~ 2,18258 pounds)
If you assemble the tire on wide rims not to put more pressure than 30 PSI. It could blast.
This offer includes 1 piece only
Thick Brick 24 x 3.0 Whitewall (75-507)
THE ultra fat custom tire !!!
The ultimate custom cruiser and lowrider tire for maximum show performance!
Compatible with :
Classic Cycle rims - 24" 30 - 82 mm wide
Specifications:
ETRTO: 75 - 507
Width of the inflated tire: ~ 75 mm
Mounted on an 82 mm wide rim, the tire is approximately 87 mm wide.
Total diameter of the tire mounted on a 82 mm wide rim: ~ 665 mm
Weight: ~ 1.3 kg
Height: Thick Brick tire is built approximately 66 mm above the rim edge
Pressure: 30 - 40 PSI / 2.1 - 2.8 bar
Please check the spacing to the frame and/or fork
We recommend not to inflate the tire above 30 PSI / 2.0 bar for rims that are too wide, otherwise the sidewall thread may tear.
Scope of delivery: 1 piece
Alu Hub, Bolt on, black for front wheel for Disc Brake
Sealed bearings
Mounting size: 100 mm (~3,94 inches)
Flange width: 58 mm (~2,28 inches)
Axle Length: 155 mm (~6,10 inches)
Pitch Circle Diameter: 58 mm (~2,28 inches)
Spoke Holes: 36 Holes 14G = 2 mm (~0,08 inches) Spokes
Weight: ~ 335g (~0,73 pounds)
with black bolts
Bolt on. NO quick release!!
Aluminium Alloy Rim 20 inch., 82 mm (~3,23 inches) wide
ETRTO: 406
double wall 82
Wide:
82 mm (~3,23 inches)
inner size:
75 mm (~2,95 inches)
Holes:
36
colour:
black
Rim diameter for calculating the spoke length:
383 mm (~15,08 inches)
Weight:
1000 g (~2,20 pounds)
Aluminium Alloy Rim 20 inch., 82 mm (~3,23 inches) wide with cut out
ETRTO: 406
double wall 82
Wide:
82 mm (~3,23 inches)
inner size:
75 mm (~2,95 inches)
Holes:
36 (offset from the middle 15,5 mm)
colour:
black
Rim diameter for calculating the spoke length:
383 mm (~15,08 inches)
Weight:
882 g (~1,95 pounds)
Apehanger Shorty Handlebar
chrome-plated Hi-Ten steel
dimensions: about 800 x 450 mm (~31,5 x 17,72 inches)
for 22,2 mm (~0,87 inches) stems
The decent cruiser chopper apehanger!
Apehanger Shorty Handlebar Black
black Hi-Ten steel
dimensions: about 800 x 450 mm (~31,50 x 17,72 inches)
for 22,2 mm (~0,87 inches) stems
The decent cruiser chopper apehanger!
Block Pedals 9/16 without Reflector Big Diamond Cut*
chrome-plated for bikes and motorbikes, 9/16 inch thread, pair with big diamond cut
The blocks are 98 mm (~3,86 iches) long
articles marked with* are not made for public use according to the german StVZO
(ONLY important for buyers from GERMANY!!!)
Chain 1/2 x 1/8
stainless steel
0,99 € per 10 cm (~3,94 inches)
how to order:100 cm (~39,37 inches) needed = 10 x 10 cm (~3,94 inches) = 10 x 0,99 €, when 150 cm needed (~59,05 inches) = 15 x 10 cm (~3,94 inches) = 15 x 0,99 € including one locking element (shackle) per chain
Chains cut to length on customer order are nonreturnable!
Chain Gold 1/2 x 1/8
1,09 Euro per 10 cm (~3,94 inches)
how to order:
100 cm (~39,37 inches) needed = 10 x 10 cm (~3,94 x 3,94 inches) = 10 x 1,09 €
when 150 cm (~59 inches) needed = 15 x 10 cm (~5,9 x 3,94 inches) = 15 x 1,09 Euro
including one locking element (shackle) per chain
Chains cut to length on customer order are nonreturnable
Classic Cycle Tiger Eye rearlight retro LED battery red with chrome plated casing
With Bumper
Good looking design and best quality
The Classic Cycle Retro is a rear fender with a hip vintage design and LED technology.
Operates on 2 x LR 03 (AAA; Micro) batteries.
Equipped with a powerful LED
Running time approx 70 hours on staedy light, 280 Hours on flash light
Retro design
Material: Chrome Plated Steel Base with steel Bumper and red Tiger Eye lens
Width: 30 mm (~1,18 inches)
Length: 60 mm (~2,36 inches)
Delivery on Headcard as shown
American-to-Euro Conversion kit
These beautifully machined aluminum bushings fit into the shell of a one-piece-crank bottom bracket, and are threaded to accept a:
standard threaded bottom bracket
normal 68 mm (~2,68 inches) width.
3 long CrMo bolts connect the two bushings to one another for a secure mounting.
Dished Sprocket, 10 mm (~0,39 inches) offset, 18 Teeth
1/2 x 1/8
helps to bring the chain 10 mm (~0,39 inches) out
Fits to shimano, sachs, sram, stumey archer 3-speed hubs, histop, ... etc.
Depth: ~ 15 mm (~0,59 inches)
inner diameter: 35 mm