Outer Cable Housing Black / Silver Diamondshape Metallic 2,50 m x 5 mm (~2,73 yards x 0,2 inches)
*Bling - Bling*
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Brake Set for Roller - Lever - Brakes Raleigh
for about 20 cm (~7,87 inches) long stem
brake set for roller-lever-brakes Raleigh-type, chrome-plated, complete kit
for example for ATLAS Roadster, Anchor 1936, Flying Pigeon, Hero, Hamilton
Outer Cable Housing Pink 2,50 m x 5 mm
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Outer Cable Housing Black Confetti Gloss 2,50 m x 5 mm (~2,73 yards x 0,2 inches)
*Bling - Bling*
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Outer Cable Housing Silver / Rainbow Shining 2,50 m x 5 mm (~2,73 yards x 0,2 inches)
*Bling - Bling*
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Magura MT2 hydraulic disc brake set for front and rear
High end quality!
Applications: All Mountain, Trail, eBike, Trekking, Tandem
Weight per brake without disc: ~ 345 g / ~ 0,76 lbs
Weight whole set with bolts: ~ 950g / ~ 2,09 lbs
Material:
Body: Carbo tecture
Lever: Aluminium
Caliper: Aluminium
Bolts: Steel
Brake medium: Magura Royal Blood Mineral Oil
Features:
Easy Bleed Technology / EBT
2 Pistons
Reach Adjust
Disc / Rotor: Magura Storm Ø180 mm / 7,08 inches, 6 hole, for heavy weight or gravity use
Pad mounting: Magnet and Pin
E-motor cut off switch (length of cable ~ 50 cm / ~ 19,7 inches)
Mounting: PM / IS
Color: black
Compatible with all standart Shimano STI, SRAM Trigger, SRAM und Rohloff twist-grip shifters
Comes with:
1 x rear brake ~ 150 cm / ~ 59,5 inches lengh of cable
1 x front brake ~ 70 cm / ~ 27,6 inches lengh of cable
2 x Magura adapter QM12 fpr ISF 180 / ISR-160
2 x disc / rotor Magura Storm Ø180 mm/ 7,08 inches
Bolts (6x per disc / rotor, 2x each for front and rear brake)
Manual multi language
Outer Cable Housing Rainbow 2,50 m x 5 mm (~2,73 yards x 0,2 inches)
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Outer Cable Housing Light Grey 2,50 m x 5 mm
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Outer Cable Housing Silver Confetti Gloss 2,50 m x 5 mm (~2,73 yards x 0,2 inches)
*Bling - Bling*
For shifter or brake cable
1 piece of 2.50 m (~2,73 yards) with 4 alloy endcaps
Compatible with all inner wire of 1.5 / 1.6 mm (~0,06 inches) including Shimano, XLC Jagwire, ...
Compatible with all rim or drum brakes also MTB and racing Bikes
Available in a lot of colours and designs
Sturmey Archer single-sided drum brake hubs (X-SD) Left
single side mounted hub with 70mm drum brake - Specific side mounted, left side - Solid axle - Now with high polish hubshell
Specs for Solid Axle Model HSL881
Side: Left
Axle Type: HSL881 Solid Nutted
Axle Diameter / Type: 12 mm (0,47 inches)
Axle Length: 130 mm (~5,12 inches) (Excl. M19 Hex Bolt Head of 4 mm (~0,16 inches))
Axle Protrusion Length: 50mm (~1,97 inches)
Hub Shell Material: A356 Aluminum
Bearing Type: 6001-ZZ Sealed Cartridge x 2
Spoke Holes: 36
Pitch Circle Diameter: 89.8 mm (~3,53 inches)
Flange Width: 54 mm (~2,12 inches)
Spoke Compatibility: 13G or 14G
Weight: 790g (~1,74 pounds)
Mechanical Disc Brake Caliper for the Front
Brake cable length adjustable without tools
EN 14766 approved
Suitable for Postmountsystem and IS2000 (front for 160 mm or rear for 140 mm disc).
Without cable and handle
Suitable Disc: Item Number 360593
including brake pads
Vintage Counterholder for shift cable
Inner dimension: 27 mm ( 1.06 inch)
Clamp for classic fixing of outer cables / Bowden cable
with bolt and nut
bright zinc-plated
1 piece
Hope brake adapter B for PM on IS fork 203mm / rear triangle 183 mm silver.
Hope adapter for mounting postmount brakes on IS2000 fork or frame. Can be used for rear wheel with 183 mm brake disc or front wheel with 203 mm brake disc.
Please also note the data sheet below when choosing the right adapter!
Post Mount to IS
for 183 mm rear brake disc
for 203 mm front brake disc
incl. mounting bolts
silver
Tektro Aries Sat left side for E-Bikes cut - off brakeBrake kit for use on e-bikesLever and bracket made of cast aluminium4-finger lever bladeBrake lever EL 350Brake caliper M306HTekro Aries mechanical brake with an adapter for 180 mm or rear for 160 mm disc.power cut - off brakeFunction of a power cut - off brakeThere is a sensor that sends a signal to the control unit when the brake lever is pulled to cut off the motor.Mounting side: leftWeight: 400 g.
Length of Cable: ~ 100 cmScope of delivery: brake lever and brake caliper with brake pads
Disc brake adapter from Magura QM 5, IS to PM.
Adapter enables the use of 203 mm brake discs on forks with IS 6" mount.
The adapter is screwed onto the IS mount of the fork and allows the use of a postmount brake caliper.
Front brake disc: 203 mm
Fork mount: IS 6
incl. mounting bolts
black
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Adapter for disc brake PM-PM-F180
The front adapter is designed to mount a Post Mount (PM) standard brake caliper to a frame with the same PM standard.
In this version it allows the use of a 180 mm brake disc on the fork.
Post Mount bracket
for 180 mm front brake disc
incl. mounting bolts
black
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Disc brake adapter from Magura QM12, IS to PM.
Adapter enables the use of 160 / 180 mm brake discs on forks and rear triangle with IS 6" mount.
The adapter is screwed onto the IS mount of the fork or frame and allows the use of a postmount brake caliper.
Front brake disc: 180 mm
rear brake disc: 160 mm
Fork mount: IS 6
rear mount: IS 6"
incl. mounting bolts
black
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Tektro EL 350 cn right side (only for e-bikes)Brake lever for use on e-bikesFor use also with linear pull brakes and Rapidfire shiftersLever and bracket made of cast aluminium4-finger lever bladepower cut - off brakeFunction of a power cut - off brakeThere is a sensor that sends a signal to the control unit when the brake lever is pulled to switch off the motor.Mounting side: rightWeight: 108 g.Scope of delivery: 1 piece
Tektro brake pads organic for disc brakes E10.11 green(organic) especially low noise - slightly higher wearThe Tektro brake pad pair is compatible with both cable and hydraulic brakes of the Uni MK series.hydraulic brakes of the Uni MK, as well as for other bikes and e-bikes.Compatible only for Tektro 350e brakeScope of delivery: two brake shoes and one spring clip
Brake pads for disc brakes, blue
Carrier plate: steel, blue
Dimensions of carrier plate: L: 30 mm, H: 20 mm, total height incl. pin holder: 35 mm
Scope of delivery: 2x brake pads, as illustrated
Magura QM41 disc brake adapter, IS2000
Adapter allows the use of 180 mm brake discs on the rear triangle with IS2000 mount.
The adapter is screwed to the IS mount of the rear triangle and allows the use of a postmount brake caliper.
Rear brake disc: 160 to 180 mm
rear wheel mount: IS2000
incl. mounting bolts
black
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Tektro EL 350 cn left side (only for e-bikes)Brake lever for use on e-bikesFor use also with linear pull brakes and Rapidfire shiftersLever and bracket made of cast aluminium4-finger lever bladepower cut - off brakeFunction of a power cut - off brakeThere is a sensor that sends a signal to the control unit when the brake lever is pulled to switch off the motor.Mounting side: leftWeight: 108 g.Scope of delivery: 1 piece
Hope brake adapter N for PM to IS rear wheel 180 mm silver.
Hope adapter for mounting postmount brakes on IS2000 frames. Can be used for rear wheels with 180 mm brake disc.
Please also note the data sheet below when choosing the right adapter!
Post Mount to IS
for 180 mm rear brake disc
incl. mounting bolts
silver
Nutt hydraulic brake right side for e-bikes with power cut - off.
Brake lever for use on e-bikes
Hydraulic brake
With power cut - off
Function of a power cut - off:
There is a sensor that sends a signal to the control unit when the brake lever is pulled to cut off the motor.
Mounting side: right
Weight: ~ 110 g.
Scope of delivery: 1 piece
Shimano Japan brake outer cable black 25 m 6 mm
Made in Japan
Technical data:
Material shift cable: metal, plastic
Length: 25 m
Outer diameter shift cable housing: 6.0 mm
Inner diameter shift cable sleeve: 3,0 mm
EAN: 4524667000570
Shimano part number: Y80A00260
Inner Cable Housing for Brakes 2 m (~2,19 yards)
made of stainless wire
diameter: 1,5 mm X 2000 mm (~0,06 x 78,74 inches)
with barrel nipple 7 x 6 mm (~0,27 x 0,24 inches)
ready greased
1 piece
Disc brake adapter IS PM 160F-140R
Disc brake adapter for conversion from International Standard to Postmount 140 mm on the rear wheel or from International Standard to Postmount 160 mm on the front wheel.
Postmount adapter
for 160 mm front brake disc
for 140 mm rear brake disc
incl. mounting bolts
black
Mechanical Disc Brake Caliper for rear
Nutt Hydraulic Disc Brake - Brake Caliper with Hydraulic Hosewith adapter suitable for front for 180 mm or rear for 160 mm brake discBrake hose length ≈ 175 cmOil brakeincl. brake pads and adapter
Tektro Aries Sat right side rear for e-bikes with breaker contact.
Brake kit for use on e-bikes
Lever and bracket made of a cast aluminum
4-finger lever blade
Brake lever EL 350
Brake caliper M306H
Tekro Aries mechanical brake with an adapter for 180 mm front or rear for 160 mm disc.
power cut - off brake
Function of a power cut - off brake
There is a sensor that sends a signal to the control unit when the brake lever is pulled to cut off the motor.
Mounting side: right
Weight: ~ 448 g.
Length of the Bowden cable: ~ 175 cm
Scope of delivery: brake lever, Bowden cables and brake caliper with brake pads.
Brake pads for disc brakes, green
Carrier plate: steel, green
Dimensions of carrier plate: L: 30 mm, H: 20 mm, total height incl. pin holder: 35 mm
Scope of delivery: 2x brake pads, as illustrated
Disc Brake Adapter Front IS / PM TEKTRO A5 Disc 203 mm
TRP Tektro A5 IS/PM Adapter Front 203mmThe TRP Tektro A5 IS/PM adapter for fork with IS mount and 203mm brake disc in combination with postmount caliper.
Details:
Fork/frame type: IS (International Standard).
Brake caliper type: Postmount
Brake disc diameter: 203mm front
Weight: approx. 60 g
incl. mounting bolts
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Tektro Auriga Comp IS2000/PM AQ Adapter A4 180mm HR
This adapter is for use of a 180 mm disc in combination with Tektro Auriga Comp Postmount brakes on frames with an IS2000 brake mount.Details:
PM brake caliper to IS frame.
material: aluminium
for rear
for 180mm brake disc
incl. mounting bolts
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Magura QM43, IS 2000 disc brake adapter.
Adapter for use on IS 2000 forks in conjunction with Magura Postmount calipers.
adapted to 160 mm
adapted to 203 mm for Fox 40 IS forks
incl. mounting bolts
black
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.