Fender Stays, 26 inch.
stainless steel one piece
for 80 mm (~3,15 inches) wide fenders
for axle mounting and 80 mm wide platesOverall length: approx. 370 mmmSlot for axle: ~15 x 10 mmMounting holes to mudguard: ~ 5 mm / slotted hole: ~ 20 x 5 mmDistance from axle mount centre to mounting hole to mudguard: ~ 355 mm
Spade Pedals
Black sand, silver Aluminium
9/16 inch thread, pair
Sealed bearing
CroMo Axle
Weight 390 g. /pair
Perfect Quality
For your information:
9/16 inch ~ 14.3 mm - for three-piece crank
Dished Sprocket, 10 mm (~0,39 inches) offset, 22 Teeth
1/2 x 1/8
22 Teeth
helps to bring the chain about 10 mm (~0,39 inches) out
Depth: ~ 15 mm (~0,59 inches)
Seat latch plastic clip
This elongated plastic part holds the seat of your UNI MK closed.
It is attached to a frame strut with one/two M4 bolts (depending on the year of manufacture of the bike) so that the seat can lock into place. It is compatible with all UNI MK versions from V1 onwards and all mounting parts are included.
Material: Moulded plastic
Colour: Black
Dimensions: 10cm x 1cm x 2cm (L x W x H)
Includes: Plastic seat fastener, mounting parts (3x M4 bolts, nut).
Original spare part from Urban Drivestyle Berlin!
Seat latch plastic clip
This elongated plastic part holds the seat of your UNI MK closed.
It is attached to a frame strut with one/two M4 bolts (depending on the year of manufacture of the bike) so that the seat can lock into place. It is compatible with all UNI MK versions from V1 onwards and all mounting parts are included.
Material: Moulded plastic
Colour: Black
Dimensions: 10cm x 1cm x 2cm (L x W x H)
Includes: Plastic seat fastener, mounting parts (3x M4 bolts, nut).
Original spare part from Urban Drivestyle Berlin!
DT Swiss H1950 Classic Hybrid aluminum rear wheel 27" 650B 35mm
General:
The H1950 Classic Hybrid is the right wheel for every occasion, whether on paved roads or bumpy forest trails or even for a short detour on a trail. In this wheel combine
the best DT Swiss E-BIKE technologies. Thanks to the jaw width of 35 mm, a wide range of tires can be used - suitable for any terrain. With a release of 150 kg system weight,
this wheel can be used both on E-MTBs, E-Urban bikes or fully packed touring bikes. No matter for which bike and which terrain - the H 1950 Classic Hybrid wheel is the perfect choice.
Details:
Rear wheel H1950 Classic Hybrid 27.5" 650B
Range of use: e-bike, tour, all mountain, trail
Wheel size: 27.5''
Wheel diameter: 584 mm
Rim type: Clincher (clincher and folding tires)
Inside width: 35 mm
Outer width: 40 mm
Rim height: 20 mm
Brake type: disc brake only
Brake disc mount: Centerlock
Number of holes: 32
Rear axle: 12x142 mm thru axle (12 mm ThruAxle)
Freewheel compatibility: Micro Spline 12-speed Shimano
valve hole: SV
tubeless capable: yes
maximum system weight (with complete wheelset front and rear): 150 kg (rider, bike, luggage)
recommended tire width: 60 mm - 75 mm (2.35 - 3.00)
color: black
total weight rear wheel: 1189 g
Scope of delivery:
1x DT Swiss H 1950 Classic rear wheel, 1x Tubeless valve MTB 32 mm, 1x manual (download see below).
Material:
Rim: aluminum
Hub body: aluminum
Spokes: Stainless steel
Nipple: aluminum
Freewheel: Steel
Hint:
You will also find the matching front wheel in our range.
UD special headset Ahead 1 1/8 inch black
durable and high quality 1 1/8" headset Ahead
for 1 1/8 inch shaft diameter
color: black
sealed roller bearings
Outer diameter bearing shell: 44 mm
Original headset for the UDX from Urban Drivestyle in Berlin
Not suitable for forks with threaded shaft!
Tire Kenda Knight 20 x 4.5 black
New, wide lug profile, very stable, super quality, extra wide
116 x 406
30 TPI
5-30 PSI / 0,4 -2.1 bar / 40 - 210 KPA
weight: ~ 2100 g
This tire fits on CLASSIC CYCLE 20" rims from approx. 82 mm width! However, please note clearance in frame and / or fork!
Dimensions, mounted on a 82 mm wide rim with 1,8 bar:
Width: ~ 108 mm
Height: ~ 90 mm above the rim edge
Total diameter: ~ 600 mm
Offer includes one tire only!
Charging socket XLR D 3-pole, female with sealing cap / sealing housing
Info about the XLR D 3-pole female charging connector:
Traditional chassis connector with large solder pads for easy soldering.
3-pole female chassis connector, D-shape
Solder terminals
Black plastic housing
Gold plated contacts
Info about the Neurik SCDX sealing cap / sealing housing:
With the SCDX sealing cap, D-shape chassis connectors are sealed against water, dust and dirt according to IP42 when unmated.
IP42 protection against dust and splash water
Suitable for all D-shape flush-type connectors
Snap lock
Labelling area
The dimensions of the sealing cap can be found in the data sheet below.
Scope of delivery:
1x XLR D receptacle
1x sealing cap
Single Piece!
UD Short tail section for UNI MK or Swing
The short UNI MK / Swing rear section is perfect for lifting the e-bike and moving it in confined spaces. At the same time, it gives the bike a sleek, sporty look and rounds off the vintage design of the UNI MK From.
The rear section is mounted on the rear end of the frame with only two bolts and serves as a handle for moving the machine in confined spaces. This rear section can only be fitted if the seat extension rear section is not fitted.
Features of the short tail section
Material: Chromoly steel
Color: white
Includes: short tail piece, two bolts and nuts each (M8)
Note: The tail section shows slight signs of storage.
ATTENTION: The tubes that are pushed into the frame are shortened and have a length of approx. 9,5 cm.
Spoke reflector / cat's eye oval
More safety in road traffic. This time with spoke reflectors of 60 mm clamping width. Roadworthiness is confirmed by the approved German test seal. So make sure they always remain visible, even in the dark.So that you can also enjoy your purchase for a long time, the cat's eye is equipped with stainless steel clips, which makes it more resistant to rust.
Approval mark: with German approval mark (area of application StVZO approved).
Special features: Stainless steel clips with 60 mm clamping width
Material: plastic
Colour: orange
Scope of delivery: 4 pieces
Dyno Tiki Taboo Light
The tiki light for your bike!
Original part of Dyno Taboo Tiki Beach Cruiser
Parking light, flashing or fast flashing.
For mounting on the handlebar and fender.
Alternatively you can replace the bracket and mount the Tiki on the fender.
Extension cable for Ebike
Technical data:
Connector: 2-pin HIGO / 1x Julet male, 1x open end
Water resistance: IP65
Cable length: ~ 30 cm
Plug connection: 1x red
Outer material: ABS plastic
General information:
HIGO / Julet plugs are common on many e-bikes because they provide a firm and waterproof connection. There are different types, which differ in the number of pins and thus the area of use.
A HIGO / Julet connector is generally quite firm because it is waterproof. It can be disconnected by pulling, NOT twisting. If twisted, the pins could be damaged.
Please note the arrows on the outside - they help to align and fit the connectors. When the connections are properly plugged together, no coloured plastic should be visible.
Herrmanns LED rear light bar for Racktime I-Valo wide
General information:The LED rear light set from Herrmanns was designed to fit the Racktime luggage carrier I-Valo. The slim design of the LED strip blends in perfectly with the sporty design of the rack. The electronics are well protected in the housing of the reflector mounted below.The LED bar offered here is an original spare part, suitable for Racktime I-Valo carriers.
Technical details:
Parking light function
dynamo operation
wide version ~ 124 mm wide
StVZO approved (K 910)
Scope of delivery:
1 x LED bar
Specifications:
Colour: red Type of lighting: rear lightPower source: side dynamo, hub dynamoLight source: 5 LED`sFeatures lighting: parking lightMounting option: Racktime I-Valo luggage rack
Busch + Müller dynamo rear light Toplight Flat plus
The classic.
Design: extremely flat and light, elegant reflector integrated into two circular surfaces. 70 g light.
Like all Busch + Müller rear lights: StVZO-approved.
Toplight series
Parking light
Dynamo version
StVZO-approved
Mounting luggage carrier
LED rear light
Integrated Z-large area reflector
Weight: ~ 70 g
Dimensions: ~ 33 x 112 x 54 mm
Reflector E1 for Racktime I-Valo Herrmanns tube, red StVZO
Product description General: The LED rear light set from Herrmanns was designed to fit the Racktime luggage carrier I-Valo. The slim design of the LED strip blends in perfectly with the sporty design of the luggage rack. The electronics are well protected in the housing of the reflector mounted below.
The reflector with housing is offered here. The reflector has StVZO approval.
Scope of delivery:1x reflector with housing
UD black chain wheel, multi-tooth for PAS sensor, 52 teeth
black steel chainring with 52 teethcover / chain guard and multi-tooth - mount made of aluminum
Original Urban Drivestyle Part
Urban Drivestyle mudguard stay for 20 inch fatbike
Mudguard strut, overflowing (1 piece)
for 20 x 4 inch
Material thickness: ~ 4 mm / 0,157 inches
Inner width: ~ 135 mm / 5,35 inches
Length of straight strut - measured vertically from apex to centre of mounting hole: ~ 280 mm / 11,02 inches - Mounting holes Ø: ~ 6 mm / 0,24 inches.
Original accessories Urban Drivestyle! The strut was used as an additional mounting for the Uni Boost mudguard.
Can also fit other 20 x 4 fatbike bikes such as Tucano Monster, B - Bob, Sondors Fold, etc. ... - Please note the dimensions!
Urban Drivestyle mudguard stay cranked for 20 inch fatbike
Mudguard strut, overflowing (1 piece)
for 20 x 4 inch
Material thickness: ~ 4 mm / 0,157 inches
Inner width: ~ 135 mm / 5,35 inches
Length of cranked strut - measured vertically from apex to centre of mounting hole: ~ 290 mm / 11,41 inches - Mounting holes Ø: ~ 6 mm / 0,24 inches.
Original accessories Urban Drivestyle! The strut was used as an additional mounting for the Uni Boost mudguard.
Can also fit other 20 x 4 fatbike bikes such as Tucano Monster, B - Bob, Sondors Fold, etc. ... - Please note the dimensions!
Urban Drivestyle mudguard stay for 20 inch fatbike
Mudguard strut, overflowing (1 piece)
Bolts, screws and bracket set
for 20 x 4 inch
Material thickness: ~ 4 mm / 0,157 inches
Inner width: ~ 135 mm / 5,35 inches
Length of straight strut - measured vertically from apex to centre of mounting hole: ~ 280 mm / 11,02 inches - Mounting holes Ø: ~ 6 mm / 0,24 inches.
Original accessories Urban Drivestyle! The strut was used as an additional mounting for the Uni Boost mudguard.
Can also fit other 20 x 4 fatbike bikes such as Tucano Monster, B - Bob, Sondors Fold, etc. ... - Please note the dimensions!
UD bolt accessory set for mudguards
Suitable for mounting mudguards with overflow brace!
The screw set was originally used to attach the Urban Drivestye mudguards 20x4 inch for UNI Fatbike, but can also be used for other models.
Urban Drivestyle fender strut set for 20 inch fatbike
Mudguard struts, overflowing (2 pieces)
bolts and bracket set
for 20 x 4 inch
Material thickness: ~ 4 mm
Inner width: ~ 135 mm
Length of straight strut - measured vertically from apex to center mounting hole: ~ 300 mm - mounting holes oblong hole: ~ 13 x 7 mm
Length of the cranked strut - measured vertically from the apex to the center of the mounting hole: ~ 290 mm Mounting holes ~ 6 mm
Original accessories Urban Drivestyle for e.g. the Moke, Swing or Bobber
Can also fit other 20 x 4 fatbike bikes such as Tucano Monster, B - Bob, Sondors Fold, etc. ... - Please note dimensions
UDX Mudguard Brace for 20 inch Black
Mudguard band brace (1 piece)
for 20 inch, black
Material thickness: ~ 3 mm
Inner width: ~ 113 mm
Length over all: ~ 200 mm
Mounting holes oblong hole: ~ 11.5 x 5.5 mm
2 threaded holes M4 in the apex
Original accessories Urban Drivestyle for the UDX
Original Urban Drivestyle Side Case / Hardcase
One of a kind!
Dimensions:
Length: ~ 40 cm
Height: ~ 32 cm
Width: ~ 20 cm
Mounting:
4 holes on the side for mounting in the direction of travel on the left side.
Mounting on a luggage carrier / luggage carrier plate possible.
Material: plastic
Colour: glossy black
With Urban Drivestyle logo on the lid!
Attention! The box is locked, the key is missing.
Original Urban Drivestyle Side Case / Hardcase
One of a kind!
Dimensions:
Length: ~ 40 cm
Height: ~ 32 cm
Width: ~ 20 cm
Mounting:
4 holes on the side for mounting in the direction of travel on the right side.
Mounting on a luggage carrier / luggage carrier plate possible.
Material: plastic
Colour: glossy black
With Urban Drivestyle logo on the lid!
Item has slight storage marks.
Attention! The box has no lock!
Heavy duty strut / support strut for luggage racks and cargo decks
Material: Chromoly steel
Colour: black, powder coated
Dimensions:
Total length: 42.5 cm
Distance hole centre to hole centre, large: ~ 40.5 cm
Distance hole centre to hole centre, none: ~ 34 cm
The support strut was used on the "load and delivery deck low" from Urban Drivestyle!
Original spare part from Uban Drivestyle Berlin!
Universal Fender clip stainless 124 mm
fits up to ~ 140 mm fender width
Length: ~ 142 mm
Width: ~ 25 mm
Height: ~ 28 mm
easy to mount for front or rear fender
Zéfal SPRING
Flexible bottle holder
In thermoplastic resin, the bottle cage provides excellent flexibility. The Spring is light and offers one of the best value on the market.
Characteristic
Weight: 46 g
Material: Thermoplastic resin
Color: Black
Made in Fance
Universal Fender clip stainless 40 mm
fits up to ~ 40 mm fender width
Length: ~ 46 mm
Width: ~ 29 mm
Height: ~ 20 mm
easy to mount for front or rear fender
Disc Brake Adapter Front IS / PM TEKTRO A5 Disc 203 mm
TRP Tektro A5 IS/PM Adapter Front 203mmThe TRP Tektro A5 IS/PM adapter for fork with IS mount and 203mm brake disc in combination with postmount caliper.
Details:
Fork/frame type: IS (International Standard).
Brake caliper type: Postmount
Brake disc diameter: 203mm front
Weight: approx. 60 g
incl. mounting bolts
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Tektro Auriga Comp IS2000/PM AQ Adapter A4 180mm HR
This adapter is for use of a 180 mm disc in combination with Tektro Auriga Comp Postmount brakes on frames with an IS2000 brake mount.Details:
PM brake caliper to IS frame.
material: aluminium
for rear
for 180mm brake disc
incl. mounting bolts
General information:
POSTMOUNT ADAPTERThe postmount mounting standard is used on most suspension forks and frames. There are usually PM6" (direct mounting of 160 mm brake discs), PM7" (180 mm) and PM8" (203 mm). Postmount adapters allow the mounting of different brake disc diameters.
IS 2000 ADAPTERWith the less common IS2000 standard, brake callipers or adapters are bolted to the side of the frame. With the help of adapters, postmount brake calipers can also be mounted on IS2000 frames.
Brake cable for front, pre-assembled
Outer cover:
~ 80 cm long
with end caps
Inner cable:
~ 96 cm long
diameter: ~ 1,5mm
with cylinder nipple ~ 7 x 6 mm
1 piece
Brake cable for rear, pre-assembled
Outer cover:
~ 150 cm long
with end caps
Inner cable:
~ 166 cm long
diameter: ~ 1,5mm
with cylinder nipple ~ 7 x 6 mm
1 piece
Spacer ring aluminium Ø 35 mm, 3 mm high, black
Inner diameter: 35 mm / 1.38 inches
Outer diameter: 42 mm / 1.65 inches
Height: 3 mm / 0.12 inches
Colour: black
Material: aluminium
Spacer ring aluminium Ø 35 mm, 2 mm high, black
Inner diameter: 35 mm / 1.38 inches
Outer diameter: 40 mm / 1.57 inches
Height: 2 mm / 0.078 inches
Colour: black
Material: aluminium
SHIMANO Deore XT gear indicator left SL-M770
Compatible with: SL-M770
Mounting: left
FEATURES
Light shifting operation, wider compatibility, and suitable for internal cable routing
Slim main lever body
RAPIDFIRE PLUS
Streamlined cockpit experience
Gear display positioned below the handlebar
Numbered gear display indicates gear position at a glance
OPTICAL GEAR DISPLAY
FEATURES
Light shifting operation, wider compatibility, and suitable for internal cable routing
Slim main lever body
RAPIDFIRE PLUS
Streamlined cockpit experience
Gear display positioned below the handlebar
Numbered gear display indicates gear position at a glance
OPTICAL GEAR DISPLAY
Shimano Lock Ring for Ultegra CS-650 Hyperglide, 12T
Please have a look at the data sheet under Downloads.
Original spare / accessory part from Shimano, made in Japan.
Brand new!
Single Piece!
UD Short tail section for UNI MK or Swing
The short UNI MK / Swing rear section is perfect for lifting the e-bike and moving it in confined spaces. At the same time, it gives the bike a sleek, sporty look and rounds off the vintage design of the UNI MK From.
The rear section is mounted on the rear end of the frame with only two bolts and serves as a handle for moving the machine in confined spaces. This rear section can only be fitted if the seat extension rear section is not fitted.
Features of the short tail section
Material: Chromoly steel
Color: white
Includes: short tail piece, two bolts and nuts each (M8)
Note: The tail section shows slight signs of storage.
€39.95*
This website uses cookies to ensure the best experience possible. More information...